I stopped buying based on unit price. Here's why.
I've been managing vendor relationships and facilities purchasing for a 150-person company for six years now. And up until about 18 months ago, I was a unit-price buyer. Three quotes, pick the cheapest, done. I thought that was what "good procurement" looked like.
It doesn't. The lowest number on the quote is almost never the lowest actual cost.
Here's what changed my mind. In early 2023—February, I think—we decided to add EV charging to our office garage. Just two ports, for the company cars I manage. I got four quotes. The cheapest was $480 per unit, some brand I couldn't pronounce. The ABB Terra AC Wallbox came in around $750. I went with the cheaper one. My boss thanked me for saving the department $540.
Six weeks later, that $480 charger became a $1,150 problem. The electrician found it needed a dedicated circuit we didn't have. Then the firmware locked up during a scheduled update—on a weekend, of course. We had to swap it out. The replacement was the ABB unit. It's been running without incident since, going on 14 months now.
That $540 "savings" cost us roughly $2,400 in rework, downtime, and an emergency electrician call on a Saturday. (I should add: the Saturday call alone was $380, and I spent four hours of a weekend coordinating it.)
I don't do that anymore.
What total cost of ownership actually means in practice
Now when I compare quotes, the unit price is maybe the third or fourth number I look at. Here's what I actually track:
Installation reality. A cheap charge station that needs electrical work is not cheap. An ABB Terra AC Wallbox that works with the existing panel is not expensive. I learned this the hard way. We also use the same unit for a small employee benefit—we cover part of the cost when someone's installing a home EV charging station in their garage. Same unit, same install checklist, same lessons.
Downtime exposure. We once had a solar panel racking system—not ABB, some contractor's "equivalent"—where the mounting clamps were undersized. One windstorm later, two panels were on the ground. The racking itself was $300 less than the alternative. The replacement panels and labor came to $1,800.
It's the same logic with ABB non-fusible disconnect switches. These are $40-60 parts. If one fails, your entire solar array—easily $15,000+ of equipment—goes offline until someone diagnoses and fixes it. The switch itself isn't the cost. The downtime is. The emergency service call is. The heat on your department when the office is running on generators is.
Support and parts availability. This is the one I underestimated for years. Cheap equipment has cheap support—meaning, often, no support. ABB is a global brand not because they're always the cheapest. It's because when something goes wrong at 4:45 on a Friday, someone answers the phone.
The counterintuitive part: sometimes the "expensive" brand is the cheaper choice
I know how this sounds. Like I've been won over by a sales rep and now I'm justifying premium pricing. So let me address that head-on.
Would I buy ABB for everything? No. For basic consumables—cables, brackets, office supplies—the cheapest option is fine. I'm not religious about brands. But for anything that touches infrastructure—power, charging, energy storage—the math changes.
Take the Enphase battery vs. Tesla Powerwall question, which we looked at for our backup power system last year. Both are premium-priced. Both are expensive compared to a no-name battery. But the total cost comparison isn't about the sticker price.
We looked at both. The comparison came down to installation complexity and future expansion. Tesla Powerwall, by all accounts, installs faster—fewer components, integrated inverter. Enphase is more modular—you can add capacity incrementally, which matters if your needs change. We went with Enphase in the end. Not because it was cheaper per kWh. It wasn't. Because adding capacity later meant adding a smaller unit rather than replacing the entire system.
That's what TCO thinking actually looks like. It's not "buy the most expensive thing." It's "identify the costs that hit you six months from now, and price those in."
I also check claims against FTC advertising guidelines now. Any performance or efficiency number a vendor gives me—whether it's cycle life on a battery or amperage on a disconnect switch—needs a published test standard behind it. "Trust us" isn't a spec.
"We can't afford the premium option"—and why that's wrong
I hear this from colleagues all the time: "Our budget just doesn't allow for the premium option." I get it. I've been there. But here's the thing:
The cheap option doesn't cost less. It just splits the cost across a longer timeline—with interest.
The $480 charger I bought in 2023 looked good on that quarter's budget. The $1,290 real cost hit us across two quarters. The ABB unit, at $950 all-in, cost more upfront and less over time. But our budget cycle rewards the first number and ignores the second.
If your procurement process makes the cheapest unit look like the safest choice—the one that won't get questioned—then your procurement process is broken. Mine was.
Look at the quotes again
I still compare quotes. I still look at the price column. But now I ask a different set of questions before I sign:
What does installation actually require? Who handles service if this fails? What's the lead time on replacement parts? Is the warranty process a phone number or a form that goes into a void?
I don't always choose the more expensive option. That's not the point. The point is that the cheapest option has to prove it's actually cheaper—not just on the quote, but over the life of the thing.
Most of the time, it can't. That $480 charger proved it. The undersized racking clamps proved it. The off-brand disconnect switch that failed at 7 AM on a Monday proved it.
I'm not buying premium gear because I'm scared. I'm buying it because I did the math. And the math kept pointing to the same conclusion: the unit price is a distraction. The real cost is the project.