-
Who this checklist is for
-
Step 1: Verify the legal entity, not just the brand
-
Step 2: Read the certification scope, not the certificate PDF
-
Step 3: Ask for the bill of materials — in writing
-
Step 4: Look for IEC 62941, then ask what it changed
-
Step 5: Request flash test data and EL images from your production batch
-
Step 6: Understand what OEM and private label actually change
-
Step 7: Read the warranty — and check who's behind it
-
Step 8: Test the paperwork before the container ships
-
Common mistakes
Who this checklist is for
If you're buying PV modules by the container — as a wholesaler, a distributor, or an EPC doing repeat installs — this is for you. It's also for whoever in your company has to reconcile the invoice when the delivered spec doesn't match the datasheet. In our company, that's me.
I run procurement for a mid-size solar distributor. About $2.1 million in annual module orders, spread across nine suppliers, and I answer to both our operations director and our CFO. What follows is the checklist I actually use before adding a tenth. It's eight steps, and realistically it takes two weeks of back-and-forth. Still cheaper than a bad container.
I'm not going to tell you which brand to buy. I'm going to tell you what to ask for, and what a good answer sounds like.
Step 1: Verify the legal entity, not just the brand
Start here, because everything else depends on it. Ask your sales contact for the full registered company name, the factory address, and the billing address that'll appear on the invoice. Then check that all three line up.
They often don't. Plenty of companies presenting themselves as manufacturers are trading companies sourcing from a factory they won't name. That's not automatically a dealbreaker — some trading companies are genuinely useful — but it changes what you can verify and who's on the hook when something goes wrong.
Two things to check while you're here: does the entity on the IEC certificates match the factory you're being shown, and do the bank details belong to the entity you signed with? I once had a supplier whose certificate was issued to a subsidiary, the proforma came from a second company, and payment was routed to a third. We walked. Slowly.
Step 2: Read the certification scope, not the certificate PDF
Everyone sends a certificate pack. Almost nobody reads the scope section.
What actually matters:
- The standard and the edition. IEC 61215-1 for design qualification, the IEC 61730 series for safety. Both have moved on recently — 61215 got a new edition in 2021, and the 61730 series was amended in 2023. A certificate from 2015 doesn't prove the product you're buying today is qualified.
- The exact models listed. Certification is per-model, not per-brand. If you're ordering a 585 W bifacial module and the certificate covers a 450 W monofacial, that document tells you nothing about your order.
- Which lab issued it. TÜV Rheinland, TÜV SÜD, VDE, UL, Intertek, JET — these are the names your bank and your insurer will recognize. "Our internal lab" isn't a certification body.
- Site-specific tests, if your projects need them. IEC 61701 for salt mist if you're anywhere near a coast. IEC 62716 for ammonia if you're installing near livestock operations or heavy agriculture.
If a supplier can't tell you which models are covered without going away to check, that tells you something about how organized their compliance file is. It's usually the same file you'll be asking them to pull from in six months.
Step 3: Ask for the bill of materials — in writing
BOM means bill of materials: the actual cells, glass, encapsulant, backsheet, frame, and junction box going into the module you're buying. Not the brochure version. The real one.
Why it matters: two modules that look identical at the same wattage can use different cell suppliers, different encapsulant grades, and different frame thickness. Those differences don't show up in flash test data, and they don't show up for two or three years either. They show up in the field, on your customer's roof.
Get it as a signed document attached to the purchase order. This is the step buyers skip most often, and it's the one I'd fight hardest for.
We didn't have a formal BOM-verification process for the first two years of our Asian sourcing. It cost us when we reordered "the same module" and got a different encapsulant — same datasheet, same price, different bill of materials. Nothing failed. But we couldn't tell customers the product was identical to what we'd sold them the year before, so we had to re-qualify it internally before we could ship. Three weeks of margin, gone.
Step 4: Look for IEC 62941, then ask what it changed
IEC 62941 is the quality management standard written specifically for PV module manufacturing. It isn't the same as ISO 9001. ISO 9001:2015 tells you a factory has a documented process. IEC 62941 tells you the process is specific to making modules.
Lots of factories have it. Fewer can talk about it. Ask two questions: what did the last surveillance audit flag, and what did you change as a result?
A factory that answers with something specific — "our EL inspection sampling on line 4, we moved it from AQL 1.5 to 1.0" — is telling you the system is live. A factory that answers "no findings" every single year is telling you something too.
The same logic applies to whether they publish PVEL PQP results or appear on the BNEF Tier 1 list. Both are useful signals, with one caveat that trips people up — see Step 7.
Step 5: Request flash test data and EL images from your production batch
Every module gets a flash test. Ask for the raw data from your batch, not a sample report from 2022.
What you're looking for:
- Actual measured power, not just the rated bin. If you ordered 580 W and the batch averages 578 W, that's normal binning. If it averages 571 W, ask why.
- Fill factor and Isc/Voc consistency across the batch. Wide swings point to cell-sorting problems.
- Electroluminescence images. Ask for a sample from each pallet, or at minimum a documented EL inspection report with the sampling rate stated.
Cost of asking: one email. Cost of not asking: the modules are already on a boat.
Step 6: Understand what OEM and private label actually change
If you're buying under your own brand, get the OEM agreement in writing and read the parts about who owns the certification.
Two structures are common. In one, the manufacturer holds the certificate and you're a name on the label. In the other, the certificate is issued in your name. Which one you want depends on whether you ever plan to switch suppliers — because a certificate in the manufacturer's name doesn't travel with you.
Some suppliers, Seraphim among them, run both a branded line and an OEM/private-label program, so you can compare the two structures side by side. That's genuinely useful if you're new to this, because you get to see how the drawings, labels, and warranty documents differ before you commit to one model.
While you're in that conversation, ask who handles compliance paperwork for your destination markets. Certification that's fine for the EU may not be accepted for a US utility-scale project, and a supplier who can't explain the difference is going to hand that problem back to you at the port.
Step 7: Read the warranty — and check who's behind it
Two numbers matter: the product warranty (typically 12–15 years) and the performance warranty (typically 25–30 years to 80–87% of nameplate). The rest is detail — but the detail is where the arguments live.
Look for: what voids the warranty, who pays shipping on a replacement, whether the degradation curve is linear or stepped, and whether the warranty transfers to a second owner.
Then look at the entity behind it. Here's the underrated point: a 30-year performance warranty from a company that's been operating for six years is a forecast, not a guarantee. That's why buyers lean on bankability lists. Just don't confuse them with quality.
BNEF Tier 1 measures bankability — it's tied to whether a manufacturer has supplied projects that secured non-recourse financing. It says nothing about how well the modules are made. I've seen Tier 1 modules with sloppy EL images and non-Tier 1 modules that were immaculate. Use Tier 1 as a financing filter. Use Steps 1 through 5 as a quality filter.
Step 8: Test the paperwork before the container ships
This is the one people skip, and it's the one that costs the most money.
Before the goods leave, get the proforma invoice, commercial invoice template, packing list, and certificate of origin in your hands. Then walk them past whoever processes your payments.
What goes wrong: entity name mismatches (Step 1 again), HS codes your customs broker wasn't expecting, a typo in your own company name on the certificate of origin, an invoice in a currency your ERP can't process without a manual override. None of it is a product problem. All of it is a delay, and delays cost demurrage.
I knew I should've run the first invoice from a new supplier past our accounting team before the container left, but we'd done three clean orders and I figured "what are the odds?" The odds showed up as a mismatched billing address on the certificate of origin that took eleven days to reissue. Not really their fault. But it was our money sitting on a dock.
Common mistakes
- Leading with price. Price is the last thing to negotiate, not the first. Once you've verified scope, BOM, and warranty, you'll know what the quote is actually for — and most of the time, two quotes that look 8% apart are quoting different products.
- Treating a sample as a batch. A hand-picked sample tells you almost nothing. The flash data and EL images from your actual production run tell you everything.
- Accepting a certificate without reading the model list. This is the single most common gap I find when I audit a supplier file someone else assembled.
- Skipping the invoice test. It's fifteen minutes of work that prevents three weeks of warehouse storage fees.
- Assuming Tier 1 means quality. It means bankable. Those aren't the same thing, and I've watched buyers learn that the expensive way.
- Not writing any of this down. Verbal answers don't survive staff turnover. Put the BOM, warranty terms, and entity names in the purchase order file, so the next person doesn't have to start over.
Eight steps, one supplier file, and a two-week clock. The first supplier you run through this will feel slow. The fourth one will feel routine — and by then, the questions are doing the filtering for you.